5 / 2 0 0 6 V E R S I O N 1 . 1 CENTAURUS PRIME Integrations, Custom Programming, Consulting Trane-485 Gateway Guide
C E N T A U R U S P R I M E 7777 RS422 Communications Installed jumpers: Baud0, Baud1, Data DCD, Data RTS, J2 (end of line only), J3 (end of lin
C E N T A U R U S P R I M E 8888 NOTE about removing the CS-485: For RS-232 or Ethernet applications, the CS-485 module is not used, and
C E N T A U R U S P R I M E 9999Gateway Overview Picture 1.3, Gateway Overview and Identification Trane Trunk 4 1 Amp Fuse Remove Cover for Po
C E N T A U R U S P R I M E 10101010Commissioning the Gateway with the Local User Interface Creating and Downloading the GATEWAY.INI file The foll
C E N T A U R U S P R I M E 11111111MUST match! If the SOCKET.CFG specifies a different IP address from the GATEWAY.INI file, you wil
C E N T A U R U S P R I M E 12121212// -------------------------------------------------------------------------- // // “BACNET_NETWORK” is used
C E N T A U R U S P R I M E 13131313Local Mode Menu Options Once connected via the local mode port you may press <enter> at any time to disp
C E N T A U R U S P R I M E 14141414State: "AutoDiscovery" on Trunk: 1, VAV Device #5 State: "AutoDiscovery" on Trunk: 1, VA
C E N T A U R U S P R I M E 15151515AUTODISCOVERY: You may SAVE and MERGE all trunk auto-discovery maps. ARE YOU SURE? If so, enter "
C E N T A U R U S P R I M E 16161616TagID: "VAV#4, TRUNK 1 (MB #1)" is ON-LINE & RELIABLE TagID: "VAV #1, TRUNK 2 (MB #61)"
5 / 2 0 0 6 V E R S I O N 1 . 1 I N T E G R A T I O N S , C U S T O M P R O G R A M M I N G , A N D C O N S U L T I N G Trane-485 G
C E N T A U R U S P R I M E 17171717(A)ll: View all configured devices. DEV: (S)elect, (A)ll, (D)etail, (O)ff-line, (C)omm Stats, (X)-it :A
C E N T A U R U S P R I M E 18181818TagID: "VAV #4, TRUNK 1 (MB #1)" statistics: Packets Today: 463 RX Errors Today: 0
C E N T A U R U S P R I M E 19191919 MB Reg 10011 (DI) "Damper Forced Closed " Fld: 0 NORMAL (0-state) MB Reg 10012
C E N T A U R U S P R I M E 20202020 BACnet ID 8 (AI) "Damper/Valve Pos " Fld: 24 ==> 24.00 BACnet ID 9 (
C E N T A U R U S P R I M E 21212121PNT: You may select an OBJECT ID to target into. Enter a valid, existing, Object ID (1 to 49999) : 3000
C E N T A U R U S P R I M E 22222222Now, before you can control a point object you must first have selected a device number and point
C E N T A U R U S P R I M E 232323236 Minimum On/Off Trane: Miscellaneous 7 Custom Programming—High Trane: Demand Limiting 8 Manual Operator Trane
C E N T A U R U S P R I M E 24242424 (P)riority: (BACnet ONLY) Use this to select the priority that you will issue subsequent contr
C E N T A U R U S P R I M E 25252525 Field In / Out Counts : 0 / 0 Field Value : 0.000 Field Hi / Lo Range : 255.000 / 0.000 En
C E N T A U R U S P R I M E 26262626WCH: (Q)uiet, (1),(2),(3),(4) to watch trunks; (V)erbose, (M)odbus, (X)-it :1 *** TRUNK 1 is now being MONIT
Table of Contents Introduction i C H A P T E R 1 Gateway Installation, Basic Information 1 Summary 1 Single Board Computer Basics 2 Connectin
C E N T A U R U S P R I M E 27272727AI 30003 Active Cooling SP Used Counts: 76 = 76.00 AO 40004 OCCUPIED Heating SPT Counts: 71 =
C E N T A U R U S P R I M E 28282828 Receiving a file from the Gateway (downloading) From the dos prompt, you must type “DOWN filename” (filenam
C E N T A U R U S P R I M E 29292929Click Transfer > Receive File: Enter the location to save the file and make sure that Xmodem is selected an
C E N T A U R U S P R I M E 30303030Setting up the BACnet System After the Gateway is ready to go and you have your database configured, one of t
C E N T A U R U S P R I M E 31313131Modbus & BACnet Point Mapping Device Point Mapping for VAV-1s and VariTranes Monitor Control Older (VAV-
C E N T A U R U S P R I M E 3232323210014 / 314 14 / 414 Min. Setpoint Forced Maximum Heating Forced 0=AUTO; 1=FORCED 10015 / 315 15 / 415 Ma
33333333 Index (A)larms, 15, 16 (C)ontrol, 13, 14, 22, 24 (C)ontrolled, 15, 16 (D)etail, 17, 18, 19, 20, 21, 22, 24, 25 (D)evices, 15 (H)elp
C E N T A U R U S P R I M E 1111 Gateway Installation Basic Information Summary his section will help to give a basic overview and quick
C E N T A U R U S P R I M E 2222configuration. Single Board Computer Basics The Single Board Computer used in Centaurus Prime Gateways is the Eth
C E N T A U R U S P R I M E 3333Connecting Power to the Gateway Power connections are made by removing the 2 screws on either side of the terminal
C E N T A U R U S P R I M E 4444avoid ground-loops). This is a two-wire trunk, so it does not matter if you land the field trunk wires on TX+/TX-
C E N T A U R U S P R I M E 5555device to reliably transmit data over long distances (up to 4000 feet). The CS485 has many features not normally f
C E N T A U R U S P R I M E 6666 OUT Enables 4-wire operation RX is receive pair TX is transmit pair J15 Connects isolated RS-485 commo
Komentarze do niniejszej Instrukcji